National Instruments FP-3000 Uživatelský manuál Strana 27
- Strana / 118
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 2 Installation and Configuration
FieldPoint FP-3000 User Manual 2-10
©
National Instruments Corporation
This is the amount of power the network module consumes from the power
supply to power itself and the I/O modules. It does not include any power
consumed by devices that you wire to the terminal bases.
The operating instructions for each FieldPoint I/O module contain power
consumption information.
Power-On Self Test (POST)
The power-on self test (POST) is a test suite that the FP-3000 performs at
power up to verify its own operational status. The test takes several
seconds. The test is non-invasive and therefore does not affect the operation
of the network, nor does it affect any of your field wiring connected to the
terminal bases in the bank.
If the self-test suite fails, the FP-3000 does not participate in the network
communication traffic, eliminating potential conflicts with the other banks
in your network.
The FP-3000 indicates POST failure through the POWER and STATUS
LEDs. Refer to the section LED Indicators for more information.
Connect the FP-3000 to the Fieldbus Network
The FP-3000 can be one of 32 devices connected to a Fieldbus network.
The connection is made through the 9-pin male Dsub Fieldbus connector
on the FP-3000, shown in Figure 2-11.
- FieldPoint 1
- FP-3000 1
- Network Module User Manual 1
- Important Information 3
- Chapter 3 5
- Chapter 4 6
- Contents 10
- About This Manual 13
- FP-3000 Network Module 14
- Overview 14
- Function Blocks 16
- PID Control 16
- Block Instantiation 16
- Interoperability 17
- HotPnP (Hot Plug and Play) 17
- Field Upgradability 17
- Figure 2-5 21
- DIN Rail Clip 21
- Figure 2-9 25
- Connect Power to the FP-3000 26
- Power-On Self Test (POST) 27
- LED Indicators 29
- Updating the FP-3000 Firmware 32
- Example Applications 36
- Fieldbus Using FP-3000 37
- Assign a Tag to the New Block 38
- Select the Module and Channel 38
- Set the Input Range 39
- Scale the Reading 39
- Set Up Scheduling 40
- Bring the Block Online 41
- Getting Started 41
- Taking Temperature Readings 42
- Create an FP-TC-120 Block 42
- Controlling a Heating Element 45
- Set the Output Range 46
- Scale the Output 46
- Instantiate a PID Block 48
- Scale the PID 48
- Tune the PID 50
- Alarming 50
- PV_SCALE 51
- HI_ALM parameter. The 52
- Block Reference 53
- Types of Function Blocks 54
- DI (Discrete Input) 55
- DO (Discrete Output) 55
- CDO (Complex Discrete Output) 55
- Chapter 4 Block Reference 56
- UNACKNOWLEDGED 59
- ALARM_STATE/UPDATE_STATE 59
- TIME_STAMP 60
- Status Handling 60
- Substatus 61
- Target Mode 62
- Actual Mode 63
- Permitted Mode 64
- Normal Mode 64
- FP-3000 Specific Parameters 65
- FIELDPOINT_CHANNEL 66
- FIELDPOINT_MODULE 66
- FP_AI_100_RANGE 66
- FP_AI_110_RANGE 66
- FP_AI_111_RANGE 66
- FP_AO_200_RANGE 67
- FP_CJC_SOURCE 67
- FP_MOD_STATUS 67
- FP_NOISE_REJECTION 67
- VERSION_INFORMATION 69
- Configuring the FP-3000 70
- Write Lock 71
- Troubleshooting 72
- Appendix B Troubleshooting 73
- I/O Module Problems 74
- Fieldbus Parameters 78
- Table C-1. Error Codes 80
- BLOCK_RESET 81
- CHECKBACK 81
- CLR_FSTATE 82
- CONFIRM_TIME 82
- CONTROL_OPTS 83
- CYCLE_SEL/CYCLE_TYPE 83
- DD_RESOURCE 83
- FEATURE_SEL/FEATURES 85
- FF_SCALE 85
- Table C-6 87
- Hard Types 87
- IO_OPTS parameter 90
- NV_CYCLE_T 91
- OP_CMD_CXO 92
- OUT_HI_LIM 92
- OUT_LO_LIM 92
- OUT_SCALE 92
- PV_FTIME 93
- RCAS_OUT 94
- ROUT_OUT 94
- RS_STATE 95
- SAFEGUARD_CL 95
- SAFEGUARD_OP 95
- SET_FSTATE 95
- SHED_OPT 95
- SHED_RCAS 96
- SHED_ROUT 96
- SIMULATE 96
- SP_HI_LIM 96
- SP_LO_LIM 96
- SP_RATE_DN 97
- SP_RATE_UP 97
- STATUS_OPTS 97
- UPDATE_EVT 99
- WRITE_ALM 99
- WRITE_LOCK 99
- WRITE_PRI 99
- XD_SCALE 99
- Advanced Function 100
- Block Behavior 100
- BKCAL_IN 101
- BKCAL_OUT 101
- Remote Cascades 102
- Fault State and Mode Shedding 103
- Manual mode 104
- Auto mode 104
- Specifications 105
- Technical Support Resources 106
- Telephone and Fax Support 107
- Glossary 108
Související produkty a manuály pro Software National Instruments FP-3000
Software National Instruments 320682C Uživatelský manuál
(454 stránky)
(454 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.252 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce