National-instruments E Series Uživatelský manuál Strana 4
- Strana / 132
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
National Instruments Corporation v DAQCard E Series User Manual
Table
of
Contents
About This Manual
Organization of This Manual ........................................................................................xi
Conventions Used in This Manual ................................................................................xii
National Instruments Documentation ...........................................................................xiii
Related Documentation .................................................................................................xiv
Customer Communication ............................................................................................xiv
Chapter 1
Introduction
About the DAQCard E Series .......................................................................................1-1
What You Need to Get Started ......................................................................................1-2
Software Programming Choices ...................................................................................1-2
LabVIEW and LabWindows/CVI Application Software ...............................1-2
NI-DAQ Driver Software ...............................................................................1-3
Register-Level Programming ..........................................................................1-4
Optional Equipment ......................................................................................................1-5
Custom Cabling .............................................................................................................1-5
Unpacking .....................................................................................................................1-6
Chapter 2
Installation and Configuration
Installation .....................................................................................................................2-1
Configuration ................................................................................................................2-2
Chapter 3
Hardware Overview
Analog Input ..................................................................................................................3-2
Input Mode ......................................................................................................3-2
Input Polarity and Input Range .......................................................................3-3
Considerations for Selecting Input Ranges ......................................3-6
Dither ..............................................................................................................3-6
Multichannel Scanning Considerations ..........................................................3-7
Analog Trigger ..............................................................................................................3-9
This document was created with FrameMaker 4.0.4
- DAQCard E Series 1
- User Manual 1
- Important Information 3
- Contents 4
- Chapter 4 5
- Table of Contents 6
- Appendix F 7
- Organization of This Manual 10
- About This Manual 11
- Related Documentation 13
- Introduction 14
- What You Need to Get Started 15
- Software Programming Choices 15
- NI-DAQ Driver Software 16
- Register-Level Programming 17
- Optional Equipment 18
- Custom Cabling 18
- Unpacking 19
- Installation and 20
- Configuration 20
- Hardware Overview 23
- Analog Input 24
- Table 3-3 27
- Figure 3-3 29
- Analog Trigger 31
- Digital I/O 34
- Timing Signal Routing 35
- Programmable Function Inputs 36
- DAQCard Clocks 36
- Signal Connections 37
- Figure 4-1 38
- Table 4-1 39
- Table 4-2 43
- DAQCard-AI-16XE-50 44
- Table 4-3 45
- Types of Signal Sources 48
- Input Configurations 48
- + Vg 49
- Signal Sources 51
- Floating Signal Sources 52
- (typically 100 k 53
- Figure 4-6 55
- Figure 4-7 56
- Power Connections 58
- Timing Connections 58
- Figure 4-9 59
- Timing I/O Connections 59
- SCANCLK Signal 62
- EXTSTROBE* Signal 63
- TRIG1 Signal 63
- TRIG2 Signal 65
- STARTSCAN Signal 66
- Figure 4-18 67
- STARTSCAN Input Signal Timing 67
- Figure 4-19 68
- CONVERT* Signal 69
- AIGATE Signal 70
- SISOURCE Signal 71
- UISOURCE Signal 72
- GPCTR0_SOURCE Signal 73
- GPCTR0_GATE Signal 74
- GPCTR0_OUT Signal 74
- GPCTR0_UP_DOWN Signal 75
- GPCTR1_SOURCE Signal 75
- GPCTR1_GATE Signal 76
- GPCTR1_OUT Signal 77
- GPCTR1_UP_DOWN Signal 78
- FREQ_OUT Signal 79
- Field Wiring Considerations 80
- Calibration 81
- Self-Calibration 82
- External Calibration 82
- Other Considerations 83
- Specifications 84
- 86
- Stability 87
- Timing I/O 88
- Physical 90
- Environment 90
- Transfer Characteristics 92
- Amplifier Characteristics 92
- Dynamic Characteristics 93
- Digital Trigger 95
- Power Requirement 95
- Triggers 95
- Optional Cable Connector 96
- Descriptions 96
- Figure B-1 97
- Figure B-2 98
- PC Card Questions and 99
- Operation 100
- Resources 100
- Resource Conflicts 102
- Common Questions 103
- Analog Input and Output 105
- Timing and Digital I/O 105
- Select_Signal 106
- GPCTR_Watch 107
- Power-Management Modes 108
- Table E-1 109
- Customer Communication 110
- Fax and Telephone Support 111
- Technical Support Form 112
- Configuration Form 113
- Documentation Comment Form 114
- Glossary 116
Související produkty a manuály pro Hardware National-instruments E Series
(67 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce