National Instruments NI 9233 Uživatelský manuál

OPERATING INSTRUCTIONS AND SPECIFICATIONSNI 92334-Channel, ±5 V, 24-Bit IEPE Analog Input Moduleni.com/manualsDeutschFrançais

NI 9233 Operating Instructions and Specifications 10 ni.comThe NI 9233 also has TEDS circuitry. For more information about TEDS, visit ni.com/info and

© National Instruments Corp. 11 NI 9233 Operating Instructions and Specificationsfrequency depends on the data rate. Figure 5 shows typical passband f

NI 9233 Operating Instructions and Specifications 12 ni.comThe relative phases of these signals also have a frequency-dependent delay. The variation i

© National Instruments Corp. 13 NI 9233 Operating Instructions and SpecificationsFigure 6. Phase Nonlinearity of the NI 92330.450.15420–2–40.100.050.

NI 9233 Operating Instructions and Specifications 14 ni.comStopbandThe filter significantly attenuates all signals above the stopband frequency. The p

© National Instruments Corp. 15 NI 9233 Operating Instructions and Specificationsshare a single master timebase source. Refer to the software help for

NI 9233 Operating Instructions and Specifications 16 ni.comNote The cRIO-9151 R Series Expansion chassis does not support sharing timebases between mo

© National Instruments Corp. 17 NI 9233 Operating Instructions and SpecificationsSpecificationsThe following specifications are typical for the range

NI 9233 Operating Instructions and Specifications 18 ni.comData rates1 (fs)fs ≤ 25.65 kS/s... , n = 2, 3, ..., 25fs > 25.

© National Instruments Corp. 19 NI 9233 Operating Instructions and SpecificationsAC cutoff frequency responseInput range ...

NI 9233 Operating Instructions and Specifications 2 ni.comThis document describes how to use the National Instruments 9233 and includes specifications

NI 9233 Operating Instructions and Specifications 20 ni.comCommon-mode voltage range(AI– to earth ground) ... ±2 V maxIEPE excita

© National Instruments Corp. 21 NI 9233 Operating Instructions and SpecificationsOvervoltage protection (with respect to chassis ground)For an IEPE se

NI 9233 Operating Instructions and Specifications 22 ni.comChannel-to-channel matchingGainTypical... 0.07 dBMaximum...

© National Instruments Corp. 23 NI 9233 Operating Instructions and SpecificationsCrosstalk (fin = 1 kHz)Paired channels(0 and 1, 2 and 3)...

NI 9233 Operating Instructions and Specifications 24 ni.comTotal harmonic distortion (THD)Intermodulation distortion (–1 dBFS)DIN 250 Hz/8 kHz 4:1 amp

© National Instruments Corp. 25 NI 9233 Operating Instructions and SpecificationsPower RequirementsPower consumption from chassisActive mode ...

NI 9233 Operating Instructions and Specifications 26 ni.comHazardous LocationsU.S. (UL) ... Class I, Division 2

© National Instruments Corp. 27 NI 9233 Operating Instructions and SpecificationsElectromagnetic CompatibilityThis product meets the requirements of t

NI 9233 Operating Instructions and Specifications 28 ni.comCE ComplianceThis product meets the essential requirements of applicable European Directive

© National Instruments Corp. 29 NI 9233 Operating Instructions and SpecificationsOperating shock(IEC 60068-2-27)... 30 g, 1

© National Instruments Corp. 3 NI 9233 Operating Instructions and SpecificationsSafety GuidelinesOperate the NI 9233 only as described in these operat

NI 9233 Operating Instructions and Specifications 30 ni.comMaximum altitude... 2,000 m Pollution Degree (IEC 60664) ...

© National Instruments Corp. 31 NI 9233 Operating Instructions and SpecificationsCalibrationYo u can obtain the calibration certificate and informatio

NI 9233 Operating Instructions and Specifications 32 ni.comWhere to Go for SupportThe National Instruments Web site is your complete resource for tech

© National Instruments Corp. 33 NI 9233 Operating Instructions and SpecificationsKorea 82 02 3451 3400, Lebanon 961 (0) 1 33 28 28, Malaysia 1800 8877

© 2004–2008 National Instruments Corp. All rights reserved.373784F-01 Sep08National Instruments, NI, ni.com, and LabVIEW are trademarks of National In

NI 9233 Operating Instructions and Specifications 4 ni.comCaution Substitution of components may impair suitability for Class I, Division 2.Caution Fo

© National Instruments Corp. 5 NI 9233 Operating Instructions and SpecificationsSpecial Conditions for Marine ApplicationsSome modules are Lloyd’s Reg

NI 9233 Operating Instructions and Specifications 6 ni.comConnecting the NI 9233The NI 9233 has four BNC connectors that provide connections for four

© National Instruments Corp. 7 NI 9233 Operating Instructions and SpecificationsEach channel has a BNC connector to which you can connect an Integrate

NI 9233 Operating Instructions and Specifications 8 ni.comFigure 2. Connecting a Grounded IEPE Sensor to the NI 9233Figure 3. Connecting a Floating

© National Instruments Corp. 9 NI 9233 Operating Instructions and SpecificationsThe NI 9233 analog input channels are referenced to the chassis ground